The Tramex roofing master kit is a non-destructive flat roof scanner kit for point-of-contact leak detection, tracing, moisture measuring, and surveying.
The Tramex RMK is the complete kit for a Roofing Professional, including the Dec Scanner and the RWS Roof & Wall Scanner allowing for continuous and point-of-contact, non-destructive surveying of moisture conditions in roofing and waterproofing systems up to 6 inches in depth. The kit also allows for non-destructive measurement of moisture conditions in concrete decks and pin readings in wood decks and roofing materials, relative humidity readings, and ambient and dew point conditions using the Tramex CMEX5 digital moisture meter and probes.
This kit comes in a protective heavy-duty wheeled carry case with die-cut foam lining. It is used to perform ASTM D7954. Bluetooth connectivity to the Tramex Meters App allows for visualization of Tramex CMEX5 readings and data reporting to mobile devices, to GeoTag test results, allowing you to create, save, and share photos, reports, and charts, as well as see your CMEX5 meter screen on your phone when extending to hard to reach places.
Kit Contents
- Dec Scanner
- RWS – Roof and Wall Scanner + telescopic handle (for use on roofs)
- Concrete Moisture Encounter X5 – CMEX5
- App available for Android and iOS (phone not included)
- Hand-held electrode with 7.8″ (200mm) insulated pins
- 10″ (260mm) narrow RH probe
- Hole punch
- Infrared Thermometer
- Extension Handle for CMEX5
Dec Scanner
The Tramex Dec Scanner is a mobile non-destructive impedance scanner designed for the instant surveying of moisture conditions in roofing and waterproofing systems per ASTM D7954.
| Comparative Max. depth of penetration: | 6” (152 mm) |
| Measuring Range: | 0 to 100 |
| Limitations: | Some EPDM, Butyl rubber roofing and other conductive roofing |
Roof and Wall Scanner – RWS
The Tramex RWS Roof and Wall Scanner is a multi-mode non-invasive impedance scanner designed for the instant, precise and non-destructive evaluation of moisture conditions and leak tracing in roofing per ASTM D7954 and in wall systems of the building envelope.
| Depth of penetration: | 4″ (100mm) |
| Sensitivity: | Four Ranges:> |
| Roofing Mode with high and low sensitivity. | |
| EIFS / Foam Roof Insulation Mode with high and low sensitivity. |
Concrete Moisture Encounter X5 – CMEX5 – Measuring Range:
The Tramex Concrete Moisture Encounter X5 is a non-destructive digital multi-moisture meter for concrete decks providing instant and precise quantitative measurement of the moisture content of concrete using Gravimetric testing as a baseline. The CMEX5 incorporates a built-in hygrometer and plug-in ports for the relative humidity probe and pin-type probe testing of roofing materials.
| Depth of penetration in concrete: | approx. ¾” (20mm) |
| Moisture content for Concrete: | 0 → 6.9 % |
| Comparative for Gypsum floor screed: | 0 → 12 |
| CM Equiv Anhydrite/Concrete: | 0→2.7 / 0→4.3 |
| Reference scale: | 0 → 100 |
| Relative Humidity: | 0 → 99% |
| (with optional Hygro-i2 ® probe): | Humidity accuracy: 0% → 99%RH +/- 2% @ 25°C / 77°F |
| Moisture content for wood (with optional wood pin probes): | 5 → 30 % |
Infrared Thermometer IRT2
The IRT2 is a handheld, dual laser, non-contact Infrared Thermometer with 12:1 distance to spot ratio and audible and visible high/low set point alarms. It is used to measure and display surface temperatures within the range of -58ºF to 1202º (-50°C to 650°C) and has an accuracy of approximately 1 to 1.5% (see Specifications for details). The IRT2 has a fast response time (0.15 sec) and is powered with a 9V battery and complies with Class II UK/EU laser safety standard EN60285.
| Temperature range: | -58ºF ~ 1202ºF (-50 to 650 ºC) |
| Distance to Spot ratio: | D:S = 12:1 |
| Display resolution: | 0.1 ºF(0.1ºC) <1000 1ºC >1000 |
| Accuracy for targets: | Assumes ambient operating temperature of 73 to 77ºF (23 to 25 ºC) -58ºF ~ 68ºF (-50 ~ 20ºC)
±4.5ºF (2.5ºC) 68ºF ~572ºF (20ºC ~300ºC) ±1.0% ± 1.8ºF (1.0ºC) 572ºF ~ 1202ºF (300ºC ~650ºC) ±1.5% |
| Repeatability: | -58~68ºF (-50~20ºC) : ± 2.3ºF (1.3ºC) 68~1202ºF (20~650ºC) : ±0.5% or ±0.9ºF (0.5ºC) |
| Response time: | 150ms |
| Spectral response: | 8~14um |
| Emissivity: | Digitally adjustable from 0.10 to 1.0 |
| Over range indication: | LCD will show “—-” |
| Polarity: | Automatic (no indication for positive polarity); Minus (-) sign for negative polarity |
| Diode laser output: | <1mW, Wavelength 630~670nm, Class 2 laser product |
| Operating temp.: | 32 to 122ºF ( 0 to 50ºC) |
| Storage temp.: | 14 to 140ºF (–10 to 60ºC) |
| Relative humidity: | 10%~90%RH operating, <80%RH storage |
| Power supply: | 9V battery, NEDA 1604A or IEC 6LR61, or equivalent |
| Safety: | “ CE ” Comply with EMC |
Specifications of Kit:
| Size: | 41.2″ x 21.1″ x 12″ (1045mm x 535mm x 305mm) |
| Weight: | 59.5lbs (27kg) |
| Power: | 4 x 9 volt PP3 Batteries, 2 x AALR6 ALKALINE Batteries (included) |
The Tramex roofing master kit is a non-destructive flat roof scanner kit for point-of-contact leak detection, tracing, moisture measuring, and surveying.
The Tramex RMK is the complete kit for a Roofing Professional, including the Dec Scanner and the RWS Roof & Wall Scanner allowing for continuous and point-of-contact, non-destructive surveying of moisture conditions in roofing and waterproofing systems up to 6 inches in depth. The kit also allows for non-destructive measurement of moisture conditions in concrete decks and pin readings in wood decks and roofing materials, relative humidity readings, and ambient and dew point conditions using the Tramex CMEX5 digital moisture meter and probes.
This kit comes in a protective heavy-duty wheeled carry case with die-cut foam lining. It is used to perform ASTM D7954. Bluetooth connectivity to the Tramex Meters App allows for visualization of Tramex CMEX5 readings and data reporting to mobile devices, to GeoTag test results, allowing you to create, save, and share photos, reports, and charts, as well as see your CMEX5 meter screen on your phone when extending to hard to reach places.
Kit Contents
- Dec Scanner
- RWS – Roof and Wall Scanner + telescopic handle (for use on roofs)
- Concrete Moisture Encounter X5 – CMEX5
- App available for Android and iOS (phone not included)
- Hand-held electrode with 7.8″ (200mm) insulated pins
- 10″ (260mm) narrow RH probe
- Hole punch
- Infrared Thermometer
- Extension Handle for CMEX5
Dec Scanner
The Tramex Dec Scanner is a mobile non-destructive impedance scanner designed for the instant surveying of moisture conditions in roofing and waterproofing systems per ASTM D7954.
| Comparative Max. depth of penetration: | 6” (152 mm) |
| Measuring Range: | 0 to 100 |
| Limitations: | Some EPDM, Butyl rubber roofing and other conductive roofing |
Roof and Wall Scanner – RWS
The Tramex RWS Roof and Wall Scanner is a multi-mode non-invasive impedance scanner designed for the instant, precise and non-destructive evaluation of moisture conditions and leak tracing in roofing per ASTM D7954 and in wall systems of the building envelope.
| Depth of penetration: | 4″ (100mm) |
| Sensitivity: | Four Ranges:> |
| Roofing Mode with high and low sensitivity. | |
| EIFS / Foam Roof Insulation Mode with high and low sensitivity. |
Concrete Moisture Encounter X5 – CMEX5 – Measuring Range:
The Tramex Concrete Moisture Encounter X5 is a non-destructive digital multi-moisture meter for concrete decks providing instant and precise quantitative measurement of the moisture content of concrete using Gravimetric testing as a baseline. The CMEX5 incorporates a built-in hygrometer and plug-in ports for the relative humidity probe and pin-type probe testing of roofing materials.
| Depth of penetration in concrete: | approx. ¾” (20mm) |
| Moisture content for Concrete: | 0 → 6.9 % |
| Comparative for Gypsum floor screed: | 0 → 12 |
| CM Equiv Anhydrite/Concrete: | 0→2.7 / 0→4.3 |
| Reference scale: | 0 → 100 |
| Relative Humidity: | 0 → 99% |
| (with optional Hygro-i2 ® probe): | Humidity accuracy: 0% → 99%RH +/- 2% @ 25°C / 77°F |
| Moisture content for wood (with optional wood pin probes): | 5 → 30 % |
Infrared Thermometer IRT2
The IRT2 is a handheld, dual laser, non-contact Infrared Thermometer with 12:1 distance to spot ratio and audible and visible high/low set point alarms. It is used to measure and display surface temperatures within the range of -58ºF to 1202º (-50°C to 650°C) and has an accuracy of approximately 1 to 1.5% (see Specifications for details). The IRT2 has a fast response time (0.15 sec) and is powered with a 9V battery and complies with Class II UK/EU laser safety standard EN60285.
| Temperature range: | -58ºF ~ 1202ºF (-50 to 650 ºC) |
| Distance to Spot ratio: | D:S = 12:1 |
| Display resolution: | 0.1 ºF(0.1ºC) <1000 1ºC >1000 |
| Accuracy for targets: | Assumes ambient operating temperature of 73 to 77ºF (23 to 25 ºC) -58ºF ~ 68ºF (-50 ~ 20ºC)
±4.5ºF (2.5ºC) 68ºF ~572ºF (20ºC ~300ºC) ±1.0% ± 1.8ºF (1.0ºC) 572ºF ~ 1202ºF (300ºC ~650ºC) ±1.5% |
| Repeatability: | -58~68ºF (-50~20ºC) : ± 2.3ºF (1.3ºC) 68~1202ºF (20~650ºC) : ±0.5% or ±0.9ºF (0.5ºC) |
| Response time: | 150ms |
| Spectral response: | 8~14um |
| Emissivity: | Digitally adjustable from 0.10 to 1.0 |
| Over range indication: | LCD will show “—-” |
| Polarity: | Automatic (no indication for positive polarity); Minus (-) sign for negative polarity |
| Diode laser output: | <1mW, Wavelength 630~670nm, Class 2 laser product |
| Operating temp.: | 32 to 122ºF ( 0 to 50ºC) |
| Storage temp.: | 14 to 140ºF (–10 to 60ºC) |
| Relative humidity: | 10%~90%RH operating, <80%RH storage |
| Power supply: | 9V battery, NEDA 1604A or IEC 6LR61, or equivalent |
| Safety: | “ CE ” Comply with EMC |
Specifications of Kit:
| Size: | 41.2″ x 21.1″ x 12″ (1045mm x 535mm x 305mm) |
| Weight: | 59.5lbs (27kg) |
| Power: | 4 x 9 volt PP3 Batteries, 2 x AALR6 ALKALINE Batteries (included) |
